
For most decks, a privacy screen about 6 feet tall, measured from the ground on the side the neighbors see from, blocks the majority of views. A 6-foot fence should block most views from ground level, and 6 feet is also the figure many cities use as the ordinary limit for side and rear yards. The catch is that a deck sits above the ground. A screen that works at ground level can be too short once you are standing on a raised platform, and a screen that is tall enough can still be illegal if it breaks a local height, setback or HOA rule. This guide shows how to pick the height, where it goes wrong, and what to confirm before anything gets built.
If your deck is being replaced or newly designed, the screen is best planned as part of the deck, not bolted on afterward. Our team builds decks, railings and covers with an in-house crew, and we handle permitting, so the height question is settled on paper before the first post goes in. You can see how we approach that on our Everett deck design service.
Cactusdecking
Plan Privacy Into Your Deck Design
Cactusdecking designs custom decks in Everett, with permitting handled by an in-house crew so privacy considerations can be planned before construction.
Visit
TL;DR
- Plan on roughly 6 feet for a screen at ground level. On a raised deck, measure from where people actually stand and sit, not from the ground.
- Test the height before you build: mark it with stakes or ladders and check it against the real line of sight from your seat and from the neighbor’s windows.
- Extra privacy without a taller wall: 12 to 18 inches of lattice on top of a fence is a common design move.
- Height limits are local. Many cities cap rear and side yards at 6 feet and front yards at 4, and fences over 6 feet often need a permit. HOAs can be stricter.
- Check the rules first, then build to the lower of the legal limit and the height your sightlines need.
Table of Contents
Start with what you are trying to block
A privacy screen is not one height. It is the answer to a specific view. Before you pick a number, walk your deck and answer three questions:
- Who is looking? A neighbor’s ground-floor window, a second-story window, a street, a walking path, or a shared fence line each need a different height.
- Where are you when you want privacy? Standing at a grill, sitting at a table, or lying in a lounger. Seated eye level is much lower than standing eye level, so a family that mostly sits can get away with a lower screen than someone who entertains on their feet.
- Which direction is the view coming from? Most decks only need screening on one or two sides. A full perimeter wall is rarely necessary and, as one landscape designer quoted by Architectural Digest points out, building taller than necessary adds cost and can make a yard feel smaller and more enclosed.
The goal is the shortest screen that fully blocks the sightline you care about. That keeps cost, permit exposure and light loss down.
Why a raised deck changes the math
A 6-foot fence is calibrated for someone standing on the ground. Put the floor of your deck 3 feet above grade and the top of that same fence is effectively 3 feet above your standing eye level only, with your head at roughly the 8-foot mark relative to the ground. Anyone on the deck can look over the top at a neighbor, and anyone on a second floor next door can look down into your seating area.
There are two ways to think about it:
- Screen height above the deck floor. For privacy from ground-level neighbors, you want the screen to rise well above the eye level of whoever is standing on your deck. That is the height you design to, not the height of the fence at the property line.
- Screen height above grade. This is usually what the city or HOA measures. A screen attached to a raised deck can count as a fence or structure at its total height from the ground, so a 6-foot screen on a 3-foot-high deck may be treated as a 9-foot structure.
That second point is where many projects get stuck. The rules below show how differently jurisdictions measure, which is why the legal check belongs before the design is final.
How to test your height before you build
The cheapest way to avoid a wrong number is to see it. Washington State University Extension, writing about living privacy screens, recommends that you use the line of sight, with stakes or ladders, to mark the screen’s exact location and preferred height before settling on a layout. The same method works for any screen, living or built.
Here is a practical version:
- Pick your seats. Put furniture where it will actually sit, including the grill and the dining table.
- Set a stand-in at the planned screen location. A ladder, a tall stake or a helper holding a board works. Mark the proposed top height with tape or string.
- Check from the seated position. Sit and look toward the problem view. Can you see the neighbor’s window or patio over the top?
- Repeat standing. If you are fine seated but exposed standing, decide which matters more for how you use the deck.
- Check from the other side. Have someone stand at the neighbor’s window or yard and look back. Privacy works in both directions, and this is the view you are actually trying to block.
- Adjust in 6-inch steps. A few inches often decides whether a view is blocked, so move the mark up or down until the line of sight is cut.
Do this at different times of day. Low winter sun and leaf-off trees change what neighbors can see, and in the Pacific Northwest, deciduous screening plants give little coverage in colder months.
Typical heights by situation
Use these as starting points, then confirm with the stake test.
| Situation |
Starting height |
Notes |
| Ground-level patio, neighbor at ground level |
About 6 feet |
Blocks most views from the ground |
| Low deck (a step or two up) |
6 feet from grade, check seated and standing |
Often still workable within a 6-foot limit |
| Raised deck, one-story neighbor |
Screen tall enough above the deck floor to clear standing eye level on the exposed side |
May exceed the 6-foot zoning figure |
| Two-story neighbor looking down |
A single fence rarely solves it |
Consider a cover or pergola-style roof over the seating area |
| Need a bit more privacy, legal height maxed out |
Add 12 to 18 inches of lattice |
Common design approach that is lighter-looking than a taller solid fence |
Notice the two-story row. A taller wall is not always the answer when the view comes from above. Overhead coverage handles angles that a vertical screen cannot, which is where deck cover installation service come in.
Lattice, slats and open screens
How solid the screen is affects how tall it needs to be. A fully solid panel blocks more at a lower height. A slatted or louvered design lets air and light through, but you give up some privacy at certain angles.
Lattice is the easiest way to gain a few extra inches of screening. Designers add 12 to 18 inches of lattice above a fence when more privacy is needed, and the guidance presents it as a way to gain screening with less visual heaviness than raising the entire fence. Some codes treat open sections differently from solid ones, which can work in your favor. In Eustis, Florida, for example, interior side and rear setbacks allow open fences up to 8 feet and opaque fences up to 6 feet, with an option for 2 feet of open fencing above. That is one city, not a national rule, but it shows why the type of screen matters as much as the height.
For ideas on materials and layouts that suit a deck, our guides on deck privacy ideas and blocking neighbors’ views from your deck go further, including plant screens.
Height limits are local: what cities actually say
There is no single U.S. height limit for privacy screens. Cities, counties and HOAs set their own, and the numbers cluster around 3 to 4 feet in front, 6 feet in side and rear yards, and 8 feet as a ceiling. A few real examples show the pattern.
Orlando, Florida. In residential districts, fences may be up to 4 feet in front yards and 6 feet in side, street-side and rear yards, with 8 feet allowed in side and rear yards that abut commercial or industrial property. The city also says fences must not obstruct corner or driveway sight-visibility triangles.
Wichita and Sedgwick County, Kansas. The city’s white paper sets a general maximum of 8 feet, measured on the side with the least vertical exposure above finished grade. Along urban standard roads, fences over 80% opaque are capped at 3 feet within 20 feet of street right-of-way and driveway intersections.
Sammamish, Washington. The city’s handout lists 6 feet for rear and side yards, 4 feet for front yards, and 3.5 feet within a 15-by-15-foot sight-distance triangle. Requests for fences up to 8 feet tall and no more than 32 feet long may be considered through a Type I Construction Permit when the fence sits along a shared side or rear line and is backed by a neighbor agreement and recorded documents.
Redmond, Washington. The fence code says fences over 6 feet require a building permit, while fences of 6 feet or less are exempt from that permit. Its listed residential zones generally allow 6 feet and other zones 8 feet, subject to sight-clearance rules.
Two patterns repeat. First, 6 feet is the common ordinary limit, and going above it usually triggers a permit or special approval. Second, sight-triangle rules near driveways and corners can cap height far below 6 feet in the places where a screen is most tempting.

These are examples from other cities. Your own city or county sets your number. For Everett-area homeowners, our guide on Everett deck setback rules explains how setbacks affect deck projects and permit timing. Confirm the screen’s height limit with your city’s permit office before you commit to a design.
Slopes, grade and how height is measured
The same screen can measure differently depending on who is holding the tape. The Newport Hills HOA in Washington is a clear example: its 2025 guidelines measure height vertically from the average finished grade at the base and require fences on slopes to be stepped, with tops level. Wichita measures on the side with the least vertical exposure, which means a fence on a slope can be judged by the lower side.
In practice, ask these before you design:
- Is height measured from the ground on my side, the neighbor’s side, or the average of both?
- Does a screen mounted on a deck count as a fence, or as part of the deck structure?
- Does a fence on a slope have to step down, or can it follow the grade?
On a sloped Northwest lot, these answers can decide whether your plan fits.
HOA rules come on top of city rules
Meeting the city limit does not settle it. HOA approval is still required where applicable, even when a permit exemption applies. HOAs often go lower or stricter. The 2025 Newport Hills guidelines, for instance, cap fences, walls and screening plants at the lesser of the city maximum or 8 feet, with a 3-foot limit within 5 feet behind the front property line.
So the working rule is: your maximum is the lowest of the city limit, the HOA limit and any sight-line rule at your corner or driveway. Get the HOA’s approval in writing before construction.
It depends on where you live, but the research gives a useful sense of the odds. In Orlando residential districts, a 12-foot fence exceeds the listed limits, and a 7-foot fence goes beyond the ordinary 4- and 6-foot limits, though it may be allowed up to 8 feet in side and rear yards that abut commercial or industrial property. Fences over 6 feet require a permit there. In Eustis, fences over 6 feet require signed and sealed drawings.
The takeaway is that 7 feet is sometimes possible with approvals, and 12 feet almost never is for a residential screen. If you are above the limit and still exposed, change the approach: add lattice where allowed, move the screen closer to the seating area (a screen near you blocks a steeper angle than one far away), add overhead cover, or use plants.
A useful geometry point: the closer the screen is to where you sit, the lower it can be to block the same sightline. A 5-foot screen right beside a seating area can do the job of a 7-foot fence at the property line, and a screen built into the deck itself sidesteps many fence rules, though it still has to meet local structure and permit requirements.

Screen height and railing height are different things
If a screen attaches to the deck, it does not replace the guardrail. Guardrails exist for fall protection and have their own height and spacing requirements, and screens built into them have to keep those guards safe and code-compliant. Our guides on deck railing height and guardrail versus handrail code cover what inspectors look for, and deck railing ideas shows styles that integrate privacy panels. Horizontal slats look great but are not right for every deck, so check our note on horizontal railing safety.
Choosing a living screen instead
Hedges and tall planters can provide privacy where a solid structure is limited. WSU Extension advises making sure a hedge’s mature width fits the space, so a plant that looks narrow in a pot does not overrun your deck in a few years. Some HOA guidelines count plant screening toward the same height cap as fences, as in Newport Hills, so plants are not automatically exempt.
A quick pre-build checklist
- Mark the proposed height with stakes or ladders and check seated, standing and from the neighbor’s side.
- Decide whether the screen stands on the property line, attaches to the deck, or both.
- Confirm the city limit for your zone, how height is measured, and whether a permit is needed above 6 feet.
- Check corner and driveway sight-distance rules.
- Get HOA approval in writing if you have an HOA.
- Talk to the neighbor on the shared line. Some cities require a written agreement for taller fences.
- Make sure the screen does not interfere with the guardrail’s safety function.
Where a deck builder earns their keep
Height, permits, structure and railing code all meet at the same point on a deck, and a mistake on one affects the others. When we design a deck, the privacy screen is planned alongside the footprint, the posts and the railing, so the height is checked against the local rules while the plan is still on paper. Our in-house build crew does the construction, and we handle the permitting for the project.
If you are replacing a worn deck, this is the moment to fix privacy too. See our deck replacement service, or look at the new deck installation service page if you want the screening, stairs and lighting designed as one outdoor space. We build with composite, PVC or cedar, and our installations are warranty-backed. For a look at finished work, see this composite deck in Everett.

If you are in Everett, Marysville or the surrounding area, start with a conversation about your deck and your sightlines through Cactus Decking.
Our view: plan privacy into the deck, not around it
Most privacy problems we hear about are really planning problems. A homeowner builds a 6-foot fence, steps onto a raised deck, and finds the neighbor’s window is still in plain sight. Or they design a handsome screen, then learn it counts toward a height limit they did not know existed.
Our approach is to settle the questions in order: who is looking, from where, how the city and any HOA measure height, and only then which materials and style. A screen that is part of the deck’s design can sit close to the seating area, where it does the most with the least height. That tends to look better and stay inside the rules.
We build with composite, PVC or cedar, and our own crew, not subcontractors, does the work, so the plan you approve is the one that gets built. The Northwest climate is hard on exposed wood and fasteners, which is another reason we like to choose the screen material together with the deck material.
Vlad
FAQ
What is the best privacy screen height for a deck?
About 6 feet is the usual starting point, because a 6-foot fence should block most views from ground level. On a raised deck, measure the screen from where you stand and sit, and confirm the real number with a stake or ladder test.
Do I need a permit for a privacy screen over 6 feet?
Often yes. Redmond, Washington requires a building permit for fences over 6 feet, and Orlando requires one too. Rules differ by city, so check with your local permit office before you build.
Can I cut a privacy screen panel to size?
Many panels are cut to fit, but follow the manufacturer’s instructions for the specific product and keep post spacing and fasteners as the panel was designed to be supported. If the screen attaches to a railing, make sure the cut does not change the guardrail’s strength or spacing.
How do I get more privacy without going over the height limit?
Move the screen closer to the seating area, add 12 to 18 inches of lattice where the code allows it, or cover part of the deck from above. Overhead cover helps most when the view comes from a second-story window.
Does the HOA matter if the city allows my height?
Yes. HOA approval is still required where it applies, and many HOAs set lower caps than the city. Get approval in writing before construction starts.
Sources
- 61 Privacy Fence Ideas to Stylishly Seclude Your Outdoor Space, Architectural Digest
- Living Privacy Screens, Washington State University Extension
- Fence Guide, City of Orlando
- Fencing Guidelines, City of Eustis
- Fences in the City of Wichita and Sedgwick County, white paper
- Residential Fences, Handout No. 220, City of Sammamish
- Fences, Redmond Zoning Code
- Newport Hills HOA Architectural Guidelines, effective April 1, 2025
Recommended